Tel:
+604-305 1055
Email: sales@prominent-supplies.com.my

Prominent Supplies (M)
Sdn Bhd

58-G, Jalan Nagasari 1,
Taman Nagasari,
13600 Perai,
Pulau Pinang, Malaysia.
+604-305 1055
+604-399 6355

TCL, TCM Series Cylinder

TCL, TCM Series Cylinder Tri-rod Cylinder Cylinder Pneumatic Components


Product Feature

1. JIS standard is implemented.

2. Two guides of special bearing steel and linear bearing or bronze bearing guide are used to prevent rotating. They can bear high torque and radial load.

    ¡ïNote: Steel ball linear bearing: It is suitable for elevation action of cylinder or the situation requiring high precision and high bearing ability, especially for the situation requiring low fraction action process.

      Bronze sliding bearing: it is suitable for the action that has radial load resistance. Compared with normal cylinder of same use, the horizontal impact resistance is doubled and it has stronger torsion rigidity.

3. Drive unit and guide unit are in the same barrel that no additional accessories are needed with minimal space required. The air intake is optional and it is convenient to install.

4. The bottom, back side and fixing plate of main body respectively has two exact orientation orifices (See ΦPA orifice and the orifice in XX point), which can provide orientation installation with high precision for the special situation.

5. Options of switch mounting with provision 4 mounting slots.

6. Special design of main body provides multi-mount;

Installation & Usage
 

1. When load changes in the work, the cylinder with abundant output capacity shall be ed.

2. Relative cylinder with high temperature resistance or corrosion resistance shall be chosen under the condition of high temperature or corrosion.

3. Necessary protection measure shall be taken in the environment with higher humidity, much dust or water drops, oil dust and welding dregs.

4. Dirty substances in the pipe must be cleared away before cylinder is connected with pipeline to prevent the entrance of particles into the cylinder.

5. The medium used by cylinder shall be filtered to 40μm or below.

6. The cylinder shall avoid the influence of side load in operation to maintain the normal work of cylinder and extend the service life.

7. Anti-freezing measure shall be adopted under low temperature environment to prevent moisture freezing.

8. If the cylinder is dismantled and stored for a long time, please conduct anti-rust treatment to the surface. Anti-dust cap shall be ed into the inlet and outlet ports. As the precision of the manufacture and  guide is high, never dismantle the fixed block or cylinder cover without permission.

Ordering code

TCL SERIES TRI-ROD CYLINDER SIZE CHART :

(mm) 12 16 20 25 32 40 50 63 80 100
10                    
20                    
25                    
30                    
40                    
50                    
60                    
70                    
75                    
80                    
90                    
100                    
125                    
150                    
175                    
200                    
225                    
250                    

Bore Size
(mm) 12 16 20 25 32 40 50 63 80 100
TCLJ
added
                   
 
TCM TRI-ROD CYLINDER SIZE CHART :
Stroke                                         Bore Size                              
(mm) 6    10 12 16 20 25 32 40 50 63 80 100
5                        
10                        
15                        
20                        
25                        
30                        
40                        
50                        
60                        
70                        
75                        
80                        
90                        
100                        
125                        
150                        
175                        
200                        
225                        
250                        
 
Bore Size
(mm) 6    10 12 16 20 25 32 40 50 63 80 100
TCMJ
added
                       

 


Please leave your enquiry here, we will reply as soon as possible.
Name*  
Company Name  
Product Interested  
Quantity  
Email*  
Contact No.*  
Attachment  
*only support gif, jpeg, jpg, png, pdf
Messages*  

Switch to Mobile Version
Subscribe Newsletter
1
Hello! Thanks for visiting my site. Please press Start button to Contact with Admin :)

Start